Request Your Service

 

 

On this page below you can find lots of good insights related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Mounting a bathtub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old bath tub with a new one is also a moderately challenging job. If the old bathtub is conveniently easily accessible, the task can relocate easily; if you need to open a wall to remove the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure you have certified on your own for the work as well as fit trying it. Instead of hiring a contractor to take control of a halfway-completed task, it is much better to consider using one prior to you begin. Chances are you might need a professional plumber to make tube links.
This article will aid you mount a brand-new bath tub in your restroom if you have actually already acquired a new tub as well as do not require to change the setup of your previous water supply pipelines.
Your tools and product checklist ought to comprise the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installation

To start with, the supporting structure provided with the bath needs to be fitted (if needed) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last placement.

 

 

Removing Old Taps

If you need to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be fairly problematic due to the restricted access that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Installing the Bathtub

Using the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four little points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the outermost flexible faucet port to the suitable supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Activate the supply of water and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the bathtub should wait till the tub has been made use of a minimum of once as this will certainly settle it into its last setting.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washing machines are in place in between the tap as well as the sink. Secure the faucet in position with the manufacturer given backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the area where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, bring about complications with moisture and also possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, as well as are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or waterproof sticky and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you liked our piece on Tools You Need to Install a New Bathtub . Thank you so much for taking time to browse our article. Enjoyed our post? Please share it. Let others locate it. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.

Get A Free Quote